UMI Performance Torque Arm Relocation Kit- T5 & 700R4 | 2228-R Camaro 1982-92

UMI Performance Torque Arm Relocation Kit- T5 & 700R4 | 2228-R Camaro 1982-92

$559.99 kt
Model:3221309
Condition: NEW
Availability:
ARRIVING SOON!
Estimated arrival: 10/02/2020 (If Ordered Today)
Fitment:
Select a Vehicle or refer to the Vehicle Fitment Tab below to verify that this part fits your vehicle.
Shipping Note:Standard Delivery
Qty:

Can't Find your Part?

We'll find it for you. Give us a call at 877.589.9860 and we'll source that discontinued or hard to find part.

Why Choose Us?

No Brokerage or Duties - Canadian Owned & Operated - Shipped from Canada to your Door - Easy to Navigate Website - Access to New, Used & Discontinued Parts - Full Time Staff to Answer your Questions.

Disclaimer

Camaro Depot always recommends professional installation of our products. Buyer assumes risk of damage caused by improper installation.


  • Fits 1982 To 1992 Chevrolet Camaro - 700R4/T5 Transmission
  • Fits 1982 To 1992 Pontiac Firebird - 700R4/T5 Transmission
  • This Transmission Cross Member Is Supplied With A Built In Torque Arm Mount Removing The Torque Arm From The Transmission Tail Shaft And Protecting The Tail Shaft From Failure
  • This Cross Member Is Designed To Tuck Tight Against The Vehicle Chassis And Will Not Effect Vehicle Ground Clearance
  • This Set-up Will Work With Virtually Any Torque Arm On The Market As Long As It Bolts Into The Stock Location
  • It Will Also Work Excellently With The Stock Torque Arm When Using A 1-PIece Bushing (Item #3004)
  • This Kit Is 100% Bolt In And Requires No Drilling, No Cutting And No Welding
  • It Bolts In Place Of The Stock Cross Member Using The Existing Holes

Note: This product must be used with a solid one-piece polyurethane bushing. It will not work with the factory bushing that utilizes a two-piece design. If using a stock torque arm with this relocation kit an aftermarket polyurethane bushing must be purchased. This item can be purchased below, Item # 3004.*

The torque arm relocation kit from UMI Performance is designed to remove the front mounting point of the torque arm off the transmission and protect the tail shaft from damage. General Motors tail shaft mounted design works great for a stock driven vehicle however it is not designed to take abuse and hard launches. This set-up replaces your transmission cross member with a new stronger set-up with a built in torque arm mount. Each relocation kit is designed to fit a specific transmission and will work with virtually any stock style aftermarket torque arm as well as the factory torque arm. The relocation kit also features instant center adjustment by moving the front of the torque arm up or down. This unit is built using DOM mild steel tubing, 0.188” mild steel mounting plates and includes all appropriate hardware needed for the installation. The torque arm mount is machined from 0.250” thick mild steel and features a new clam shell for appropriately attaching the torque arm to the new cross member. This relocation kit will work with both the manual T5 and automatic 700R4 transmission. Please use the FAQ’s below for additional information.

The Vehicle Fitment Guide is to be used as a general reference. The data has been provided by our suppliers and manufacturers and may contain errors or incorrect data. Always refer to a professional to verify correct fitment for your vehicle.
Make Model Years
Chevrolet Camaro 1982 - 1987

Write a Review

Your Name:

Your Review:

Note: HTML is not translated!

Rating: Bad Good

Ask a question about

UMI Performance Torque Arm Relocation Kit- T5 & 700R4 | 2228-R Camaro 1982-92:
Your Name:


Your Email:


Question: Note: HTML is not translated!

Related Products
Shipped from Canada
No Brokerage/Duties
Canadian Owned
www.camarodepot.ca 2020