Upgrade Of Original Includes All Bushings And Hardware Decreases Deflection Between Subframe & Body Your Choice Of Black Or Red Made In USA Lifetime Manufacturer?s Warranty
…
Restoration Correct Hardware Correct hardware Like Original Includes 5 Self Threading Nuts, 5 Rubber Washers, And 2 Sheet Metal Screws Are you replacing that old worn out or dented heater box cover? This correct heater box to firewall…
Quality Replacement Supports Radiator Core Triple Chrome Plated (4) Chrome Mounting Bolts Included Easy To Mount Sold As A Pair Replaces GM #3903480 (Right) & 3903479 (Left) Fender to radiator support bars in your 1967, 1968, or 1969…
Maximum Airflow At Low RPM
Reduced Eng. Load At High RPM
Less Resistance At Hwy Speeds
More Horsepower
Better Gas Mileage
2.25 in. Projected Width
10000 RPM Rating
Standard Mounting Pattern
…
Reproduction of the vented radiator overflow jar for all 1978-79 Camaro models. This plastic bottle is manufactured with correct HOT/COLD lines as original. Cap not incuded. For radiator overflow jar cap purchase part number 371978. …
Best Quality Reproduction Fan Shroud Bracket Black Epoxy Painted Bracket Fits 67-69 Small Block Fan Shrouds Fits 67-68 Big Block Fan Shrouds Includes (2) J-nuts, (2) Lower Shroud Clips, (1) Upper U-nut The upper fan shroud mounting bracket…
The radiator core support bushings are very important parts of your Camaro so don?t forget to get the hardware when replacing the bushings. These bolts are notorious for rust and corrosion due to moisture and battery acid. This hardware…
Reproduction of Original Without Air Conditioning Cars Only For Cars with Small Block Heater Boxes Only Contains all Major Inner Heater Box Seals 1967, 1968, 1969 Camaro heater box seals are a critical replacement when working on any…
Quality Reproduction Opaque Plastic Reads ENGINE COOLANT ONLY Nice reproduction of the coolant overflow bottle cap for your Camaro. Bottles do not come with caps already installed and you will need this cap for your overflow to function…
Replacing the heater core can be done much easier before all of the dash is installed. Replace you original core today before you have a passenger's side floor and carpet full of antifreeze. NOTE: These new heater cores are slightly…
Reproduction of Original Fits LH side Tank Bracket Flange Set With Correct RH Clip Available as Part # EP-107 Upper Brackets Available Separately as EP-10 and EP-11 Quality Reproduction of often overlooked but necessary part for the proper…
Replacement Heater Core
For Cars Without Air Conditioning
Your original heater core can corrode overtime. Repalce it will our heater core that has been manufactured to meet or exceed factory specifications.
…
Restoration Correct Coolant Temperature Sensor Can Work On 68-69 But Has Incorrect Terminal Style With Mushroom Head Stud Connector For Cars With Console Gauges Fits 1967-1978 1st or 2nd Gen Camaros The coolant temperature sending unit in…
Reproduction Of Original Technically Correct For 1967 & 1968 Black Reinforced Rubber GM Markings On One Hose Only As Original The hoses on your 1967, 1968, or 1969 Camaro are absolutely vital to keep everything running smoothly and…
Reproduction Of Original Set Includes All Bushings And Hardware Needed To Mount The Radiator Core Support To The Front Subframe. Over the years, these 1970, 1971, 1972 Camaro radiator core support bushing fatigued from gravity and…
Triple Chrome Plated 23-7/8 x 5-1/4 3 Holes Fits All Except Heavy-Duty Radiator Camaro radiator supports may encounter disrepair after years of use in your 1970-1981 Camaro. If your radiator support is rusted or damaged, replacement is…
OER® fan shroud designed for use on 1970-79 Camaro models equipped with a small block V8 without factory air conditioning. Fan shrouds are manufactured with pressure-injected molded ABS material to ensure that each shroud meets or…
This is the white rope tape that seals your heater box or air conditioning evaporator case to the firewall. It comes in a 35 foot roll with six 1/8 inch strands for a total of 180 feet. Also used on the blower motor to heater box, non ac…
Tower clamps like this were used on all 1967-69 Camaro radiator hoses from the factory and being cold galvanized they were very susceptible to rust and corrosion.
Tip: Use a crescent type wrench at the square nut to hold it so it and…
Each kit contains all the correct bolts, washers and nuts used to mount the subframe body bushings. Replaces rusted, burred, stripped, or otherwise damaged originals. Excellent for use when replacing subframe bushings. This is a…
Best Quality Reproduction Camaro Fan Shroud Decal Officially Licensed GM Restoration Part Cooling System Warning Decal By now, the original cooling system in your 1967, 1968 or 1969 Camaro has been replaced, leaving your fan shroud without…
Replacement Fan Includes Locking Screw For Tighter Fit 1967, 1968, 1969 Camaro blower fans, squirrel cage, or centrifugal fans go by many names in the restoration, hot rod or daily driver world. Still, this little round wheel on your Chevy…
GM Licensed Reproduction Produced From Original Equipment Materials Correct AC Logo & RC-15# Technically & Mechanically Correct Fits 1967-72 Big Block Or Small Block Will NOT Fit 1972 Up With Coolant Recovery
…
Good Quality Replacement Blower Motor For Camaro For Camaro Without Air Conditioning Includes Squirrel Cage Blower Fan Wire Leads Incorrect For Concourse Restoration Great Part For A Daily Driver Or Weekend Warrior Because Everything Is…
The radiator core support bushings are very important part of your Camaro so don?t forget to get the hardware when replacing the bushings. This technically correct hardware kit includes everything necessary to replace that old rusted…
OER® reproduction of the original radiator overflow jar designed for use on 1989-92 Camaro and Firebird models. Manufactured in clear/white blow-formed plastic material, the overflow jar features the correct factory markings including…
My Account
